How to Bridge a Speaker?

 

When installing a new audio system in your car, it is important to ensure the speakers are getting the required power to work properly and that your amplifier is compatible with the rest of your equipment.

There are many ways to install a car audio set, and bridging a speaker is simply a process you can use to make a four-channel device compatible with a two or one-channel amplifier, thus maximizing the output of your system.

But how exactly do you bridge a speaker? That’s what we are going to discuss in this article. Come with us as we guide you through how to bridge speakers and amplifiers, plus give you a few tips and tricks to help you with the process.

How to Bridge a Speaker? [Best and Quick Way]

The best way to bridge a speaker will depend on how many channels your amplifier has. In the most common case (2-channel amplifier), you should connect the positive wire of your speaker to the positive terminal of your amp’s channel 1, the negative wire of your speaker to the negative terminal of your amp’s channel 2, and the negative terminal of your amp’s channel 1 to the negative terminal of your amp’s channel 2.

Since there are many cases and the step-by-step process will depend on the number of channels your speaker/amplifier has, we invite you to read through the article as we discuss in-depth all of the possible scenarios.

What Does Bridging a Speaker Do?

First of all, let’s understand what bridging a speaker does. In simple terms, the process will allow you to power a single speaker using a two-channel amplifier; or even a pair of speakers using a four-channel amp, for example.

Normally, each channel of your amplifier would power a single speaker, but when you bridge the amp, the two channels will work together and provide more power output.

When and Why Bridge a Speaker?

Bridging a speaker is useful when you have, for example, a speaker that requires more power output than a single channel of your amp can provide.

Let’s say you have a speaker that requires 100W of power, and each channel of your amp can only deliver 50W of output: by bridging two channels together, you end up with a power output of 100W.

Tips to Consider Before Bridging a Speaker

1. Make Sure your Amplifier Allows Bridging

By far, the most important thing you should do is to check if your amplifier allows bridging. Failing to do so could seriously damage your equipment since not every amp can handle an increased power output.

This information can be found in your amp’s owner’s manual or the manufacturer’s website.

2. Make Sure your Speaker Allows Bridging

Just like amplifiers, some speakers are not bridgeable nor designed to receive an increased amount of power. Like always, check the owner’s manual and the manufacturer’s website before you proceed.

3. Check your Speaker and Amplifier’s Power Rating

Check these specifications and calculate how many watts of power output you’re going to get by bridging your speaker. This is the only surefire way to know you won’t damage your equipment.

Tools Required While Bridging a Speaker

Check Price on Amazon

Speaker Wires

Speaker wires come in various gauges designed to handle different amounts of impedance and power output.

It is important to determine which gauge of wire you need to use to connect your speakers to your amplifier and to bridge your equipment as well. This will help avoid any damage and overheating issues with your devices.

Here is a chart to help you determine the right wire gauge for your particular use case based on your speaker’s RMS power and your wire run length:

Speaker RMS Power	Wire Run Length	Wire Gauge
Up to 500 Watts	Up to 4 Feet	12-Gauge Wire
Up to 1000 Watts	Up to 7 Feet	10-Gauge Wire
Up to 1500 Watts	Up to 10 Feet	8-Gauge Wire
Up to 2500 Watts	Up to 15 Feet	6-Gauge Wire
Up to 4000 Watts	Up to 20 Feet	4-Gauge Wire

Remember that the power output will be increased when you bridge a speaker, so take that increment into account.

Check Price on Amazon

Ring Terminals (Optional)

Ring terminals are small metal connectors you can use to create a better connection between your speaker and amplifier’s terminal and your wires. They are not necessary but can come in handy when bridging your equipment.

When attached to the end of a wire, these little connectors will allow you to screw your wire directly into the terminal instead of having to solder it. You can easily find them on Amazon or buy them for a few cents in your local electronics/general store.

To Top

How to Bridge a Speaker

Let’s take a look at the step-by-step on how to prepare to bridge a speaker. After this section, we will explain the process for each case in more detail.

Turn Off your Amplifier Completely and Disconnect the Wires

It doesn’t hurt to remember that you must turn off your amplifier completely before you bridge it. Plus, waiting a few minutes after you cut the energy is a great idea to ensure that every component inside it has been disabled. You should also disconnect your current wiring.

Determine the Impedance of your System

Bridging a speaker will affect the impedance of your circuit. In a traditional speaker setup, the impedance of the speakers is matched to the amplifier’s output impedance. However, the impedance will change when you bridge an amplifier to power a single speaker.

Since bridging doubles the voltage and power output to your speaker, the impedance will be cut in half. For example, if you have an 8-ohm speaker, the impedance will be reduced to 4 Ohms when you bridge your amp.

An important thing to consider is that not all amplifiers are designed to handle the impedance reduction that comes with bridging. Always check your amp’s owner’s manual to see if that’s the case and determine the resulting impedance of your whole circuit beforehand.

Determine the Resulting Power Output

Bridging a speaker will double the voltage and the power output going to your speaker. When you bridge an amplifier that delivers 50W of power per channel, the resulting output will be 100W.

It is extremely important to plan your resulting power output beforehand and ensure your speaker is compatible with the voltage you’re planning to feed it, as overpowering the device could potentially damage it.

Choose the Appropriate Bridging Method

As we already mentioned in this article, there are many ways to bridge a speaker, and the best method for your particular case will depend on how many channels your speaker has.

Bridging a two-channel amplifier, for example, is a different process than bridging a four-channel one. The wiring and the connections will differ.

How to Bridge a Two-Channel Amplifier

If you have a two-channel amplifier, you can bridge the device to power a single speaker.

1. Turn off and unplug your amplifier from the energy source by removing any cables connected to it.
2. Find a switch in your amplifier that says “Bridge” or “Bridged Mode.” This option must be turned on before you proceed. It is usually located at the back of the device or in the digital menu of the amp.
3. Wire the positive terminal of your amplifier’s left channel to the positive terminal of your speaker.
4. Wire the negative terminal of your amplifier’s right channel to the negative terminal of your speaker.
5. Wire the negative terminal of your amplifier’s left output to the negative terminal of your amplifier’s right output.
6. If you have a multimeter, test your circuit to ensure you have the right impedance and power output.
7. Connect your amplifier to your head unit.
8. Connect your amplifier to a power source, bring the volume all the way down, and test your circuit by gradually increasing the volume.

 

How to Bridge a Four-Channel Amplifier

Bridging a four-channel amplifier is slightly more complex than bridging a 2-channel amp, but can still be done if you follow the steps.

1. Cut the energy to your amplifier by turning it off and unplugging it from the power source.
2. Find a switch in your amplifier that says “Bridge” or “Bridged Mode” and turn it on. This option is usually located at the back of the device or in the digital menu of the amp.
3. Determine what channels you want to bridge. The most common scenario is to bridge channel 1 to channel 2 and channel 3 to channel 4, but several possible configurations exist.
4. Wire your speaker’s positive terminal to the positive terminal of your amplifier’s channel 1.
5. Wire your speaker’s negative terminal to the negative terminal of your amplifier’s channel 2.
6. On your amplifier, wire the negative terminal of channel 1 to the negative terminal of channel 2.
7. If you have two speakers, repeat the same process with channels 3 and 4 and your second speaker.
8. Test your circuit with a multimeter to ensure you have the right impedance and power output.
9. Connect your amplifier to your head unit.
10. After bringing the volume of your head unit all the way down, turn on your amplifier and work in small increments to test the sound quality.

 

How to Bridge a 2-Channel Amp to 2 Subs

Using 2 subs in an audio setup can give you a more powerful bass response and give an extra boost to your low frequencies, but you will need double the energy output to make it work. Here are the steps to do it by bridging a 2-channel amplifier.

1. Turn off and unplug your amplifier from the energy source by removing any cables connected to it.
2. Turn on the “Bridge” or “Bridged Mode” on your amplifier. There’s usually a switch at the back of the device or an option in the menu to activate it.
3. Wire the positive terminal of the first subwoofer to the positive terminal of your amplifier’s channel 1.
4. Wire the negative terminal of the same subwoofer to the negative terminal of your amplifier’s channel 2.
5. Wire the positive terminal of your second subwoofer to the positive terminal of your amplifier’s channel 2.
6. Wire the negative terminal of the same subwoofer to the negative terminal of your amplifier’s channel 1.
7. Since you’re using two subwoofers, the power output is likely very high, so its a good idea to test it with a multimeter before turning on your system. Test your impedance as well.
8. Connect your amplifier to your head unit.
9. Adjust your crossover settings to the needs of your subwoofers.
10. Turn the volume of your head unit all the way down, turn your system on and slowly bring the volume up to test the audio quality.

 

To Top

How to Bridge a 2-Channel Amp to a Single Sub

Bridging a 2-channel amp to a single subwoofer is similar to bridging any kind of speaker.

1. Cut the energy to your amplifier by turning it off and unplugging it from the power source.
2. Find a switch in your amplifier that says “Bridge” or “Bridged Mode” and turn it on. This option is usually located at the back of the device or in the digital menu of the amp.
3. Wire the positive terminal of your subwoofer to the positive terminal of your amplifier’s channel 1.
4. Wire the negative terminal of your subwoofer to the negative terminal of your amplifier’s channel 1.
5. Wire the negative terminal of your amplifier’s channel 1 to the negative terminal of your amplifier’s channel 2.
6. Test the impedance and power output with a multimeter.
7. Connect your amplifier to the power source and turn it on.
8. Adjust your crossover settings to better suit your subwoofer.
9. Turn your head unit on and gradually increase the volume to test the audio quality of your system.

How to Safely Disconnect the Speakers

 

Always disconnect your speakers before you start bridging your amplifier. Here is how to do so.

1. Turn off your head unit.
2. Open the hood of your car and find the battery. Disconnect its negative terminal. This will cut the energy to your system completely and prevent any electrical shocks.
3. Unscrew the speakers from their mountings.
4. Disconnect the wires from the back of your speakers. Depending on your particular case, the type of connector might differ (soldered, screwed-in-place, etc).
5. Remember to disconnect your amplifier from your head unit and power source as well.
6. Proceed to work on bridging your speakers.
7. After the work is done, power your system back on by reconnecting your battery’s negative terminal.

 

Check out article on ‘Best Subwoofers with Built-in Amp for Cars‘.

FAQs

Conclusion

Bridging an amplifier will double its power output. The practice can be very useful, for example, to power a single speaker that requires more voltage than an amp’s single channel can deliver.

As there are many different methods to bridge a speaker, take your particular case into consideration to decide which one will work best for you.

Keep in mind as well that while the practice might be simple, there are a lot of safety precautions and plans you must make before you bridge your speaker. This will prevent any accidents or damage to your equipment.

We hope we helped you to bridge your speaker successfully. Make sure to check our related articles about car audio, and feel free to contact us if you have any questions!